Beijer-electronics AN-BEI-H2-038 Uživatelský manuál stáhnout pdf

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12



AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping

1



BFIApplicationsSupportLibrary

ApplicationNote AN‐BEI‐P2‐038

Title ModbusRTUControlandRegisterMapping

RelatedProducts BeijerFrequencyInverterH2

Level

3

1–Fundamental‐Nopreviousexperiencenecessary

2–Basic–SomeBasicdrivesknowledgerecommended

3–Advanced–SomeBasicdrivesknowledgerequired

4–Expert–Goodexperienceintopicofsubjectmatterrecommended



Overview:

ThisdocumentprovidesinformationontheModbusRTUmemorymappingthatisimplementedintheBeijerFrequencyInverter

H2drives,detailingwhichaddressesareusedtoreadandwritedatato/fromtheBeijerFrequencyInverterH2inaModbusRTU

network.AlldataregisterswithinthedriveareHolding

Registers,andcanbeaccessedbymeansoftheModbuscommands03

ReadMultipleHoldingRegistersand06WriteSingleRegisteronly.



TheModbusRequestPDU specifies the starting registeraddressandthe numberofregisters.In this case, with some Modbus

Master Systems, it may be necessary to subtract

1 from the register number (e.g. some systems treat holding register 1 as

address0).



TheManufactureradoptsapolicyofcontinuousimprovementandwhilsteveryefforthasbeenmadetoprovideaccurateandup

todateinformation,theinformationcontainedinthisdocumentshouldbeusedforguidancepurposes

onlyanddoesnotform

thepartofanycontract.



MODBUSRTUProtocolSpecification:

ThefollowingtablehighlightsthespecificationfortheModbusRTUimplementation.



Protocol ModbusRTU

Errorcheck CRC

Baudrate ParameterSelectableasfollows:‐

9600bps,19200bps,38400bps,57600bps,115200bps(default)

Dataformat ParameterSelectableasfollows:

1startbit,8databits,1stopbits,noparity.(default)

1startbit,8databits,2stopbits,noparity.

1startbit,8databits,1stopbits,evenparity.

1startbit,8databits,1stopbits,odd

parity.

Physicalsignal RS485(2‐wire)



1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - Overview:

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping1BFIApplicationsSupportLibraryApplicati

Strany 2 - ModbusTelegramStructure:

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping10Group6:AdvancedParameterset(Level3)P

Strany 3

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping11Group8:ApplicationSpecificParameters‐

Strany 4

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping12DriveErrorCodeInformation:In the event

Strany 5

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping13ModbusExceptionResponseTelegrams:Unders

Strany 6 - DriveParameters:

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping14Appendix:RevisionHistoryVersion Comments

Strany 7

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping2ModbusTelegramStructure:ThefollowingModb

Strany 8

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping3MemoryMap:Table1:Controlandstatusregis

Strany 9

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping461 Userregister11 03,06 Read/Write62 Use

Strany 10

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping5Register8:OutputCurrentThisregisterdisp

Strany 11

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping6DriveParameters:All User Adjustable para

Strany 12

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping7Group2:Extendedparameterset(Level2)Pa

Strany 13 - Dataflowexample:

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping8Parameter RegisterNumberDescription Range

Strany 14

APPLICATIONNOTEAN‐BEI‐H2‐038 Date:15/02/12AN‐BEI‐H2‐038ModbusRTUControlandRegisterMapping9Group3:UserPIDcontrol(Level2)P

Komentáře k této Příručce

Žádné komentáře

Beijer-electronics AN-BEI-H2-038 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítačový hardware Beijer-electronics AN-BEI-H2-038. Beijer Electronics AN-BEI-H2-038 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Počítačový hardware Beijer-electronics AN-BEI-H2-038