
4 ChemicalResistance
4.1 MetalCasing
The frame and casing material is powder-coated aluminum. This powder paint
withstands exposure to the following chemicals without visible change:
Aceticacid10% Phosphoricacid4%
Citricacid10% Phosphoricacid10%
Diesel
Seawater
Distilledwater Sodiumchloride2%
Edibleoil Sodiumchloride20%
Fueloil Sulphuricacid20%
Hydrogenperoxide3%
Tap water
The powder paint shows limited resistance to the following chemicals at room
temperature:
Butanol Nitricacid3%
Hydrochloricacid 5% Nitricacid10%
Isopropylalcohol Phosphoricacid43%
Na-hypochlorite10%
Turpentine
Note:
Ifexposure toanyoftheabovechemicalsisdemanded,itisr ecommendedto
firsttestthechemicalinahiddenspotofthemetalcasing.
The powder paint shows little or no resistance to the following chemicals at room
temperature:
Aceticacid,conc. Methyl-ethylketone Toluene
Acetone
Nitricacid30% Trichlorethylene
Ammonia5%
Phenol Xylene
Ammonia,conc.
Sodiumhydroxide5% 97octaneunleadedpetrol
Ethylacetate Sodiumhydroxide30% 98octaneleadedpetrol
4.2 TouchScreenandOverlay
4.2.1 AutoflexEBA180L
Autoflex EBA 180L covers the overlay surrounding the t ouch screen.
SolventResistance
Autoflex EBA 180L withstands exposure of more than 24 hours duration under
DIN 42 115 Part 2 to the following chemicals without visible change:
Acetonitrile DieselDowney/
Lenor
(1)
Phosphoricacid(<30%)
Ajax/Vimin
solution
Ethanol Potassiumferricyanide
Alkalicarbonate
solution
(1)
Glycerine Potassiumhydroxide
(<30%)
Ammonia (<40%)
(1)
Glycol
PureTurpentine
Aceticacid(<50%)
Gumption
(1)
SBP60/95
(1)
Arielpowderin
solution
(1)
Hydrochloricacid
(<36%)
Sulfuric acid(<10%)
Bleach
(1)
Linseedoil Tomatoketchup
Castoroil Methanol Trichloroaceticacid
(<50%)
Causticsoda
(<40%)
(1)
Nitricacid(<10%) WhiteSpirit
Cuttingoil Pa raffinoil Windex
(1)
Cyclohexanol Persilpowder in
solution
(1)
Wisk
Diacetonealcohol Petroleu mspirit
(1)
-
(1)
Extremelyfaintglossingofthetexturewasnoted.
Autoflex EBA 180L withstands DIN 42 115 Part2 exposure of up to 1 hour
duration to glacial acetic acid without visible change.
Autoflex EBA 180L is not resistant to high pressure steam at over 100 °C or the
following chemicals:
Concentratedmineralacid s Benzylalcohol
Concentratedcausticsolution Methylenechloride
4.2.2 TouchScreenSurface
The touch screen surface on the operator panel withstands exposure to the following
solvents without visible change:
Solvents
Time
Acetone 10minutes
Isopropanol
10minutes
Toluene 5hours
4.2.3 AutoflexEBA180L
It is recommended to use the Autoflex EBA 180Ltouch display protection film, that
can be ordered from Beijer Electronics.
SolventResistance
Autoflex EBA 180L withstands exposureto the same chemicals as Autotex F157 or
F207 according to section Autoflex EBA 180L.
OutdoorUse
In common with all polyester based films, Autoflex EBA 180L is not sui table for use
in conditions of long-term exposure to direct sunlight.
5 OperatorPanelDrawings
5.1 Connectors
1234567
Pos. Connector Description
1
Powersupply
+24VDC(18-32V DC)
2 COM1/2 CommunicationPorts
3LAN(Port2)
1×10/100Base-T(shieldedRJ-45)
4
USB 2×USBHost2.0,maxoutputcurrent500mA
5
Headphone HeadphoneConnector
6LAN(Port1)
1× 10/100/1000Base-T(shieldedRJ-45)
7
COM3/4 CommunicationPorts
5.2 CommunicationPorts
Serialport,9 -pinfemale Serialport,9-pinfemale
Pin
COM1 COM2 COM3 COM4
1
-
RS422Tx+
RS485Tx+/Rx+
-
RS422Tx+
RS485Tx+/Rx+
2RS232RxD
-
RS232RxD
-
3 RS232TxD
-
RS232TxD
-
4
-
RS422Rx+
-
RS422Rx+
5
GND GND GND GND
6
-
RS422Tx-
RS485Tx-/Rx-
-
RS422Tx-
RS485Tx-/Rx-
7RS232RTS
--
RS422RTS+
8RS232CTS
--
RS422RTS-
9
-
RS422Rx-
-
RS422Rx-
Note:
Inordertoutilizetwocommunicationportsonthesamephysicalport,the
Y-splitcableCAB109mustbeused.
Drawingfor externalcableCAB109(drawing#Z7100-029E)isavailableonthe
website: www.beijerelectronics.com
5.3 iXT12BOutline
max. 8 mm
50
7
2249
9
242
340
322
9
9
Note:
AStepCADfileisavailableonthewebsite www.beijerelectronics.com
Order no: MAEN096C
Copyright © 2013-09 Beijer Electronics. All rights reserved.
The information in this document is subject to change without notice and is
providedas available at the time of printing. Beijer Electronics AB, including
all its group companies, reserves the right to change any information without
updating this publication. Beijer Electronics AB, i n cluding all its group
companies, assumes no responsibility for any errors that may appear in this
document. Read the entire installation manual prior to installing and using
this equipment. Only qualified personnel may install, operate or repair this
equipment. Beijer Electronics AB, including all its group companies, are
not responsible for modified, altered or renovated equipment. Because the
equipment has a wide range of applications, users must acquire the appropriate
knowledge to use the equipment properly in their specific applications. Persons
responsible for the application and the equipment must themselves ensure that
each application is in compliance with all relevant requirements, standards and
legislation in respect to configuration and safety. Only parts and accessories
manufactured according to specifications set by Beijer Electronics AB, including
all its group companies, may be used.
BEIJER ELECTRONICS A B, INCLUDING ALL ITS GROUP
COMPANIES, SHALL N OT BE LIABLE TO ANYONE FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE INSTALLATION, USE OR REPAIR
OF THIS EQUIPMENT, WHETHER ARISING IN TORT, CONTRACT,
OR OTHERWISE. BUYER'S SOLE REMEDY SHALL BE THE REPAIR,
REPLACEMENT, OR REFUND OF PURCHASE PRICE, AND THE
CHOICE OF THE APPLICABLE REMEDY SHALL BE AT THE SOLE
DISCRETION OF BEIJER ELECTRONICS AB, INCLUDING ALL ITS
GROUP COMPANIES.
Headoffice
BeijerElectronicsAB
Box426
20124Malmö,Sweden
www.beijerelectronics.com/+4640358600
Komentáře k této Příručce